On-line 3-D system for the inspection of deformable parts

In spite of the development of automated tolerance inspection systems for manufactured parts over the years, there are still processes that inevitably require manual intervention making full automation impossible in most cases; in particular when dealing with deformable parts. In most current industrial inspection systems, a deformable part under inspection must first be mechanically constrained on a rigid support or jig so as to be able to compare it with its nominal shape. This paper presents a new system to perform real-time surface inspection of deformable parts that does not require fixturing. Instead, the proposed system applies virtual forces to the part??s CAD model as if the part was installed in the fixturing device. Normally, a precise finite element method (FEM) simulation should be used to approximate the deformation that appends when the part is installed in the device. Even with a fast parallel computer, FEM is far from being real-time and cannot be used for on-line inspection. In the proposed system, a radial basis function approximation of the FEM simulation is trained off-line and used to speed-up the simulation by an order of magnitude. Experimental evaluation of the proposed system is presented for three plastic parts. Using the proposed scheme, an approximation of 0.25?mm compared with the real deformation was obtained. In this paper, statistical results are presented such as the average deviation, standard deviation, and processing time between the approximations obtained with the proposed method and with the finite element method applied to the full CAD model.     

In-plane cyclic behaviour of a new reinforced masonry system: Experimental results

This paper describes the behaviour under cyclic shear compression of an innovative reinforced masonry system, composed of horizontally perforated units, having common steel bars or prefabricated trusses as horizontal reinforcement. At the wall edges or crossings, confining columns for vertical reinforcement are built with vertically perforated units. Experimental tests to obtain information on the in-plane cyclic behaviour of the construction system were performed on masonry panels made of horizontally perforated units and on completed reinforced masonry walls. Tests on the entire system were repeated for two wall aspect ratios and two vertical stress levels, in order to force shear type and flexural behaviour. In particular, this paper presents: (a) results of shear compression tests in terms of strength, ductility parameters, energy dissipation, viscous damping and stiffness degradation, (b) strains and the effectiveness of reinforcement, (c) the influence of various parameters such as axial load, aspect ratio, and reinforcement type on the behaviour of the reinforced masonry walls, and (d) comparison of walls built with and without vertical reinforcement.     

Solid hybrid polyelectrolyte with high performance in electrochromic devices: Electrochemical stability and optical study

This paper presents a high-stability, single-phase hybrid polyelectrolyte (SPHP) applied in a large EC device (5×10 cm²) using WO₃ (electrochromic) and CeO₂–TiO₂ (counter-electrode–ion storage) electrodes, both produced by Leibniz—Institut of New Materials (Leibniz—INM, Germany). The electrochromic device exhibited excellent color and bleach reversibility, high coloration efficiency (>35 cm²/C) from the first cycle up to more than 60,000 CA cycles, and a maximum constant rate of deintercalation/intercalation (O_out/Q_in=1). Its remarkable behavior and high stability render this material an excellent candidate for application in electrochromic devices.     

Comparison of the effectiveness of four linearizing techniques used in SiGe HBT LNA at 1900 MHz and low-bias voltage

In this article, four linearizing techniques are compared with each other when they are used in a common-emitter SiGe HBT LNA. Finally, when all of them are employed together, improved linearity of the LNA is observed and more than 10 dBm of IIP3 and −5 dBm of 1-dB gain input compression point are realized when the circuit is fed with 2.4 V. © 2004 Wiley Periodicals, Inc. Int J RF and Microwave CAE 14, 144–152, 2004.     

Physical and functional characterization of PHASCL membranes

Dense semicrystalline membranes of polyhydroxyalkanoates with medium change length (PHA_SCL), polyhydroxybutyrate (PHB) and poly β (hydroxybutyrate-co-hydroxyvalerate) [P(βHB-co-XβHV)] were characterized using wide-angle X-ray (WAXS) and scanning electron microscopy. PHB membranes showed a more rugged surface than those of copolymers (0-22%HV). Properties such as swelling capacity, vapor permeability and selectivity were investigated. Swelling percentage in water-ethanol mixtures was 34% for PHB as compared to 14% for copolymers membranes. The ethanol/water selectivity (α_s) of PHB was 5.8 which shows that it is more selective than copolymers.The water vapor and ethanol vapor permeability were determined by a gravimetric technique at different temperatures by static and dynamic methods. PHB permeability was 69.5 Barrer at 30 °C and a discreet increment was observed at temperatures (30-50 °C). The difference in permeability between PHB and [P(βHB-co-X%βHV)] could be interpreted in terms of the crystallization rate, crystallite size and distribution which impact to transport properties of amorphous phase.     

SECT: An effective coding technique for polygonal geographic data

Memory occupation of geographic data and efficiency of the selection and elaboration algorithms are challenging problems in designing a system for polygonal data processing. They arise basically from the large number of polygon vertices necessary to properly approximate territory maps. Since the number of vertices is determined by the expected resolution, data compression can only be achieved by reducing the memory occupation of each point. On the other hand, more efficient algorithms are obtained if unnecessary operations are carefully avoided: in geographic data processing this is done by precisely delimiting the territory areas to be processed. In this paper, the SECT coding technique is presented, which meets both the above requirements. Its data compression capability is proved with reference to points, lines and regions coding, having considered geographic data of different density. Furthermore, the benefits it ensures in terms of both CPU time and I/O operation savings are discussed.